- #Hp laserjet pro m1217nfw initializing drivers
- #Hp laserjet pro m1217nfw initializing update
- #Hp laserjet pro m1217nfw initializing upgrade
- #Hp laserjet pro m1217nfw initializing windows 10
- #Hp laserjet pro m1217nfw initializing software
Then I started keying in the initial configuration.Check our tips and fixes! I am sure it is a corrupt image from bad firmware that they should have removed from their website years ago considering the hundreds who have complained meaning thousands affected. I am not sure the computer even sees the printer via usb in those seconds when the language and location questions are there. Then a few seconds later, the Initializing begins and the amber light starts blinking.Īre you saying those few seconds were enough to load firmware? It is only a few seconds later that the loop happens. So right after I boot, the green light power blinks, the language and location question appear. The printer is still working without any issues. Re-installing the image might have overwritten the corrupted parts.
#Hp laserjet pro m1217nfw initializing upgrade
My best guess would be a corrupted image on the printer either through a previously failed firmware upgrade or due to corruption on the printer itself. I can only speculate why the boot loop occurred.
#Hp laserjet pro m1217nfw initializing update
So: this time frame right after a hard reset can be used to trigger a firmware update via PC. It was only after the initial configuration that the boot loop reappeared. How did the same firmware resolve it? Hi Susan! I had noticed that, after a hard reset, the loop did not appear immediately.įor some reason the printer let you enter some basic settings without interruption. Plus, it is the firmware that created the loop.
#Hp laserjet pro m1217nfw initializing software
Then the software crashes when the printer is gone. How did you upload the firmware without the loop disconnecting the connection to the computer? The printer only appears connected for a couple of seconds before the loop starts again. I hope this description helps others who are also affected by this problem as I have not yet seen any other solution in the HP forum. I was able to upload the firmware when the first init-setting appeared.Īfter updating the firmware the loop was gone and the printer worked again as before. My final approach was just to try out if there would be a firmware upload possibility right after a hard reset steps as described above. Of course resetting everything required setup to the network.My first approach was to make a hard reset, i. After trying many other things you procedure worked great. Step 1 worked right away! Thanks so much! Thanks for the advice. I stress to other users be sure to disconnect the USB cable as even if not connected to a PC that small difference seemed to be key. Good Luck! Fixed: HP LaserJet M1217nfw MFP printer stuck at "Initializing…"Īfter surveying numerous sites for a solution, your first option worked for me. Also keep in mind that if you are on a network you can go to the IP address of the printer to reach its configuration page. I had to grab an old Windows PC and was able to get the software update loaded.
#Hp laserjet pro m1217nfw initializing drivers
The latest drivers can be downloaded at support. I did have one problem after the update which I solved by unplugging the USB cable - which makes no sense since I just used that cable to update the printer software - but hey - it worked! After that I was able to regain use of the printer. You might need to reset the printer again that will make it back to working stagemake sure you apply the latest firmware from official site.Ī solution i found was to disconnect the fax board from inside the printer. Can you just check location of your scanner head?. I have the same problem with hp lj nf of intializing acc to your advise i did it but all waste issue is same. It worked like a bought one, as they say. I had the same problem and spent several hours tearing my hair out until I found your solution. Thanks for visiting my site - Vinay Patel. This might just help someone out there who might have encountered the same thing as i did. Step 5:If your Router does not support ipv6 : disable ipv6 in your printer This works in my case. Step 3:Power on the printer and hit Right Arrrow And X Cancel button above copy button until it says permanent storage initialize. Step 3: Power on the printer and hit Copy And X Cancel button above copy button until it says permanent storage initialize. Reply 0 Kudos.Initially when it starts initializingthe scanner head moves to scan area instead of standby positionon every initialization it moves either left or right.
#Hp laserjet pro m1217nfw initializing windows 10
Operating System: Microsoft Windows 10 bit. All forum topics Previous Topic Next Topic. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Have a great day! Didn't find what you were looking for? Ask the community or Ask the Virtual Agent. Do you see this message on the printer screen? Hope this helps! Keep me posted. I have tried several reset options and do not know what to do. When I tried to set it up on my computer it is getting stuck in an "initializing loop" and it will not stop.